参照元

説明

引数

返り値

参考

実装

レジスタをスタックに保存する部分

	.align	5
ENTRY(vector_swi)
	sub	sp, sp, #S_FRAME_SIZE
	stmia	sp, {r0 - r12}			@ Calling r0 - r12
 ARM(	add	r8, sp, #S_PC		)
 ARM(	stmdb	r8, {sp, lr}^		)	@ Calling sp, lr
 THUMB(	mov	r8, sp			)
 THUMB(	store_user_sp_lr r8, r10, S_SP	)	@ calling sp, lr
	mrs	r8, spsr			@ called from non-FIQ mode, so ok.
	str	lr, [sp, #S_PC]			@ Save calling PC
	str	r8, [sp, #S_PSR]		@ Save CPSR
	str	r0, [sp, #S_OLD_R0]		@ Save OLD_R0
	zero_fp

システムコール番号を取得する部分

	/*
	 * Get the system call number.
	 */

#if defined(CONFIG_OABI_COMPAT)
	/*
	 * If we have CONFIG_OABI_COMPAT then we need to look at the swi
	 * value to determine if it is an EABI or an old ABI call.
	 */
#ifdef CONFIG_ARM_THUMB
	tst	r8, #PSR_T_BIT
	movne	r10, #0				@ no thumb OABI emulation
	ldreq	r10, [lr, #-4]			@ get SWI instruction
#else
	ldr	r10, [lr, #-4]			@ get SWI instruction
  A710(	and	ip, r10, #0x0f000000		@ check for SWI		)
  A710(	teq	ip, #0x0f000000						)
  A710(	bne	.Larm710bug						)
#endif
#ifdef CONFIG_CPU_ENDIAN_BE8
	rev	r10, r10			@ little endian instruction
#endif

#elif defined(CONFIG_AEABI)
	/*
	 * Pure EABI user space always put syscall number into scno (r7).
	 */
  A710(	ldr	ip, [lr, #-4]			@ get SWI instruction	)
  A710(	and	ip, ip, #0x0f000000		@ check for SWI		)
  A710(	teq	ip, #0x0f000000						)
  A710(	bne	.Larm710bug						)

#elif defined(CONFIG_ARM_THUMB)

	/* Legacy ABI only, possibly thumb mode. */
	tst	r8, #PSR_T_BIT			@ this is SPSR from save_user_regs
	addne	scno, r7, #__NR_SYSCALL_BASE	@ put OS number in
	ldreq	scno, [lr, #-4]

#else

	/* Legacy ABI only. */
	ldr	scno, [lr, #-4]			@ get SWI instruction
  A710(	and	ip, scno, #0x0f000000		@ check for SWI		)
  A710(	teq	ip, #0x0f000000						)
  A710(	bne	.Larm710bug						)

#endif

#ifdef CONFIG_ALIGNMENT_TRAP
	ldr	ip, __cr_alignment
	ldr	ip, [ip]
	mcr	p15, 0, ip, c1, c0		@ update control register
#endif
	enable_irq

システムコールのコードにジャンプする部分

	get_thread_info tsk
	adr	tbl, sys_call_table		@ load syscall table pointer
	ldr	ip, [tsk, #TI_FLAGS]		@ check for syscall tracing
#if defined(CONFIG_OABI_COMPAT)
	/*
	 * If the swi argument is zero, this is an EABI call and we do nothing.
	 *
	 * If this is an old ABI call, get the syscall number into scno and
	 * get the old ABI syscall table address.
	 */
	bics	r10, r10, #0xff000000
	eorne	scno, r10, #__NR_OABI_SYSCALL_BASE
	ldrne	tbl, =sys_oabi_call_table
#elif !defined(CONFIG_AEABI)
	bic	scno, scno, #0xff000000		@ mask off SWI op-code
	eor	scno, scno, #__NR_SYSCALL_BASE	@ check OS number
#endif

	stmdb	sp!, {r4, r5}			@ push fifth and sixth args
	tst	ip, #_TIF_SYSCALL_TRACE		@ are we tracing syscalls?
	bne	__sys_trace
	cmp	scno, #NR_syscalls		@ check upper syscall limit
	adr	lr, BSYM(ret_fast_syscall)	@ return address
	ldrcc	pc, [tbl, scno, lsl #2]		@ call sys_* routine
	add	r1, sp, #S_OFF
2:	mov	why, #0				@ no longer a real syscall
	cmp	scno, #(__ARM_NR_BASE - __NR_SYSCALL_BASE)
	eor	r0, scno, #__NR_SYSCALL_BASE	@ put OS number back
	bcs	arm_syscall	
	b	sys_ni_syscall			@ not private func
ENDPROC(vector_swi)

コメント


トップ   編集 凍結 差分 履歴 添付 複製 名前変更 リロード   新規 一覧 検索 最終更新   ヘルプ   最終更新のRSS
Last-modified: 2014-09-13 (土) 08:26:44